Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 5417
Search took 1.16 seconds.
Search: Posts Made By: digr
Forum: Shop & Safety Yesterday, 10:37 PM
Replies: 6
Views: 97
Posted By digr
On the self stick I used a heat gun

On the self stick I used a heat gun
Forum: Welding Yesterday, 02:38 PM
Replies: 27
Views: 473
Posted By digr
Maybe something like this with no welding

Maybe something like this with no welding
Forum: Mechanical & Electrical 01-16-2018, 10:54 PM
Replies: 10
Views: 438
Posted By digr
They worked good for what they were made for.

They worked good for what they were made for.
Forum: Fabrication 01-16-2018, 06:54 PM
Replies: 3
Views: 246
Posted By digr
Here is a drawing...

Here is a drawing (http://www.shopfloortalk.com/forums/showthread.php?t=6053&highlight=block)
Forum: Fabrication 01-16-2018, 04:38 PM
Replies: 3
Views: 246
Posted By digr
Clamp

Made another clamp and a fixture for butt welding rounds
Forum: Mechanical & Electrical 01-15-2018, 06:52 PM
Replies: 16
Views: 580
Posted By digr
A little better pic.

A little better pic.
Forum: Blacksmithing & Forming 01-13-2018, 01:48 PM
Replies: 13
Views: 415
Posted By digr
Another first class job!!!!

Another first class job!!!!
Forum: Fabrication 01-12-2018, 02:18 PM
Replies: 25
Views: 906
Posted By digr
acetylene also works:eek:

acetylene also works:eek:
Forum: Fabrication 01-11-2018, 06:39 PM
Replies: 82
Views: 3,785
Posted By digr
It did shrink, each half is shorter

It did shrink, each half is shorter
Forum: Fabrication 01-11-2018, 12:37 PM
Replies: 2
Views: 251
Posted By digr
I also have one of those Craftsman grinders, I...

I also have one of those Craftsman grinders, I run green stones for carbide on it. It is made to run 3/4" stones but I run 1" on it with about a half a nut holding the wheels but it dose a right fine...
Forum: Mechanical & Electrical 01-10-2018, 04:18 PM
Replies: 224
Views: 11,305
Posted By digr
Good to hear!!!!! Not to keep this thread going...

Good to hear!!!!! Not to keep this thread going but how big of shop does your mechanic have, can he fit two or more jobs in at one time?
Forum: Fabrication 01-08-2018, 09:09 PM
Replies: 121
Views: 3,856
Posted By digr
I think you better run out of stroke before your...

I think you better run out of stroke before your pusher hits the blades:eek:
Forum: Fabrication 01-07-2018, 03:53 PM
Replies: 12
Views: 729
Posted By digr
I used .035 solid which I find to be troublesome...

I used .035 solid which I find to be troublesome with pin holes, but I only had one on this which I ground out and re welded. Every where that I have worked with other welders running .035 it seems...
Forum: Fabrication 01-06-2018, 02:37 PM
Replies: 12
Views: 729
Posted By digr
manifold

Made a manifold for the air compressor

1 parts

2 assembly

3 testing

4 done
Forum: Mechanical & Electrical 01-05-2018, 06:23 PM
Replies: 224
Views: 11,305
Posted By digr
Did you put the dip stick back in after you got...

Did you put the dip stick back in after you got back?
Forum: Welding 01-05-2018, 03:22 PM
Replies: 24
Views: 886
Posted By digr
UK search engine...

UK search engine (https://www.mojeek.co.uk/emotions)
Forum: Welding 01-05-2018, 03:18 PM
Replies: 24
Views: 886
Posted By digr
Here are some...

Here are some (https://www.indeweld.co.uk/miller-welders-range)
Forum: Welding 01-05-2018, 03:03 PM
Replies: 38
Views: 1,251
Posted By digr
The largest carbons that I have run were 3/8" but...

The largest carbons that I have run were 3/8" but I have some 3/4" that I keep around for different things. I talked to I guy who says that he ran 3/4" carbons with two 750 amp lincoln welders tied...
Forum: Mechanical & Electrical 01-03-2018, 11:33 AM
Replies: 22
Views: 659
Posted By digr
Oil is the problem.

Oil is the problem.
Forum: Mechanical & Electrical 12-31-2017, 11:50 AM
Replies: 40
Views: 1,092
Posted By digr
When you take the cover off there should be NO ...

When you take the cover off there should be NO or NC marked inside.
Forum: Welding 12-29-2017, 06:17 PM
Replies: 38
Views: 1,251
Posted By digr
This was not nice but once when when there were...

This was not nice but once when when there were four of us welders working on a barge (welding cables laying all over hell) I sharpened a welding rod stuck it into my buddy's lead and turned on my...
Forum: Welding 12-29-2017, 06:02 PM
Replies: 43
Views: 3,044
Posted By digr
I see said the blind man...

I see said the blind man (https://www.wilhelmsen.com/marine-products/welding--surface-preparation/gas-welding--acetylene-vs-propane/),
Forum: Mechanical & Electrical 12-29-2017, 05:55 PM
Replies: 24
Views: 1,275
Posted By digr
Most everything around here is going underground

Most everything around here is going underground
Forum: Welding 12-29-2017, 05:13 PM
Replies: 43
Views: 3,044
Posted By digr
Nothing wrong with using propane, just a slower...

Nothing wrong with using propane, just a slower preheat, otherwise one can make some clean cuts. Plasma is fine if you can stand the fumes. I still use acetylene only. If I was in business and went...
Forum: Welding 12-29-2017, 03:30 PM
Replies: 38
Views: 1,251
Posted By digr
They had one of those at work and I used to tie...

They had one of those at work and I used to tie it and a 200 amp machine together to be able to run large carbons for the air ark.
Showing results 1 to 25 of 5417

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 10:06 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.