Shop Floor Talk  

Go Back   Shop Floor Talk > Search Forums

SFT Search:   
Showing results 1 to 25 of 31
Search took 0.01 seconds.
Search: Posts Made By: milomilo
Forum: Shop & Safety 02-21-2017, 10:07 AM
Replies: 297
Views: 41,580
Posted By milomilo
Mine are 2-3 feet deep closer to 3 than 2. I did...

Mine are 2-3 feet deep closer to 3 than 2. I did not use tape. I think it is a good idea though.
Forum: Shop & Safety 01-21-2017, 01:49 PM
Replies: 297
Views: 41,580
Posted By milomilo
Looking mighty good.

Looking mighty good.
Forum: Shop & Safety 09-28-2016, 08:47 AM
Replies: 297
Views: 41,580
Posted By milomilo
Did you ask him for his opinion on the concrete...

Did you ask him for his opinion on the concrete finish job?
Forum: Shop & Safety 09-24-2016, 09:58 PM
Replies: 297
Views: 41,580
Posted By milomilo
Nothing like a good fire and friends.:D

Nothing like a good fire and friends.:D
Forum: Shop & Safety 08-22-2016, 05:43 PM
Replies: 297
Views: 41,580
Posted By milomilo
Probably the last time she will let you use HER...

Probably the last time she will let you use HER garage.:devil:
Forum: Shop & Safety 08-21-2016, 10:28 PM
Replies: 297
Views: 41,580
Posted By milomilo
Probably I just can't see it in the pics, but...

Probably I just can't see it in the pics, but what type of drip edge did you put under the eaves? What type of ridge cap and type of seals are you using?
Forum: Shop & Safety 08-18-2016, 07:58 AM
Replies: 297
Views: 41,580
Posted By milomilo
I tried all the other methods, but found the dual...

I tried all the other methods, but found the dual saw worked the best. Carbide tipped counter rotating blades. Leaves a pretty smooth edge and does not over heat the tin. Requires ear protection,...
Forum: Shop & Safety 08-17-2016, 07:44 PM
Replies: 297
Views: 41,580
Posted By milomilo
What are you using to cut the tin?

What are you using to cut the tin?
Forum: Shop & Safety 08-15-2016, 08:54 PM
Replies: 297
Views: 41,580
Posted By milomilo
Probably just me, but what are you calling a...

Probably just me, but what are you calling a return board?
Forum: Shop & Safety 08-14-2016, 09:32 PM
Replies: 297
Views: 41,580
Posted By milomilo
I always put on the rafter clips before putting...

I always put on the rafter clips before putting up the walls and setting the rafters. That way no lining up the rafters, just drop them in.
Forum: Shop & Safety 08-07-2016, 09:54 PM
Replies: 297
Views: 41,580
Posted By milomilo
No nail gun or do you just need the exercise?

No nail gun or do you just need the exercise?
Forum: Shop & Safety 08-04-2016, 12:04 PM
Replies: 297
Views: 41,580
Posted By milomilo
SD is right, a copula does not pivot like a...

SD is right, a copula does not pivot like a turret.:D
Forum: Shop & Safety 08-01-2016, 08:32 AM
Replies: 297
Views: 41,580
Posted By milomilo
It is called a rat run board. The "face" board is...

It is called a rat run board. The "face" board is a fascia board and aren't you putting fascia on the gable ends too? How close to square is the framing? Measure corner to corner inside and corner to...
Forum: Shop & Safety 07-26-2016, 06:06 PM
Replies: 297
Views: 41,580
Posted By milomilo
You can find all the dimensions of J & Z channel...

You can find all the dimensions of J & Z channel and calculate the length of the metal from there. Wherever you buy your metal from should be able to figure all of this out for you if you give them...
Forum: Shop & Safety 07-18-2016, 11:08 AM
Replies: 297
Views: 41,580
Posted By milomilo
Back fill will take care of the slope issue.

Back fill will take care of the slope issue.
Forum: Shop & Safety 07-18-2016, 08:51 AM
Replies: 297
Views: 41,580
Posted By milomilo
Where did you relocate the hole?

Where did you relocate the hole?
Forum: Shop & Safety 07-15-2016, 08:50 PM
Replies: 297
Views: 41,580
Posted By milomilo
I'd go with a 55 gallon drum. Best to have more...

I'd go with a 55 gallon drum. Best to have more and not need it. I'd also keep it at least 8' away from the pad. What size drain pipe? Make sure you can access it in 2-3 years to clean out the...
Forum: Shop & Safety 07-14-2016, 08:44 PM
Replies: 297
Views: 41,580
Posted By milomilo
And your score was??????????

And your score was??????????
Forum: Shop & Safety 07-12-2016, 09:25 PM
Replies: 297
Views: 41,580
Posted By milomilo
How are you putting up the trusses?

How are you putting up the trusses?
Forum: Shop & Safety 07-12-2016, 07:28 PM
Replies: 297
Views: 41,580
Posted By milomilo
It does cut down rain and hail noise. I just put...

It does cut down rain and hail noise. I just put the steel right down on the OSB. I use foam blocks top and bottom for bugs and dirt. It is so nice to be able to walk the roof and snap chalk lines...
Forum: Shop & Safety 07-12-2016, 11:30 AM
Replies: 297
Views: 41,580
Posted By milomilo
Planned to do steel. Still time to change my mind...

Planned to do steel. Still time to change my mind I guess.

I was referring to using OSB as a sheeting regardless of what you put up as exterior siding. Sheeting in OSB really gives the building...
Forum: Shop & Safety 07-11-2016, 07:48 PM
Replies: 297
Views: 41,580
Posted By milomilo
Was not picking on you, just suggesting a...

Was not picking on you, just suggesting a different approach next time. Are you sheeting the outside of the walls with OSB or plywood?
Forum: Shop & Safety 07-11-2016, 01:17 PM
Replies: 297
Views: 41,580
Posted By milomilo
Just as a suggestion for your next one, when I...

Just as a suggestion for your next one, when I had my wood shop floor done I took a blank sheet of paper and wrote down:

Floor finish type
Slump criteria
Rebar size and quantities
Fiber
Anchor...
Forum: Shop & Safety 07-11-2016, 08:40 AM
Replies: 297
Views: 41,580
Posted By milomilo
You are going to start framing before you have...

You are going to start framing before you have the concrete issue resolved? What if it has to be jack hammered out?
Forum: Shop & Safety 07-08-2016, 10:25 PM
Replies: 297
Views: 41,580
Posted By milomilo
If you are OK with the epoxy coating, I'd throw...

If you are OK with the epoxy coating, I'd throw that in as a way to settle. That way you get a much better finished floor and all he is out is the epoxy materials and labor for application. Much less...
Showing results 1 to 25 of 31

 
Forum Jump
Web Search:

All times are GMT -5. The time now is 12:23 PM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2018, vBulletin Solutions, Inc.